PREMIUM PLUS® Exterior Paint/Primer

1 HR Dry Time
2 HR Recoat Time

23-37 m²
Coverage

Soap & Water
Clean-Up

Protect
from Freezing

Where to Use

Ideal for Wood, Vinyl and Fiber Cement Sidings; Stucco, Brick, Masonry and Fences.

Preparation

Use on properly prepared and cleaned coated and uncoated Exterior surfaces.
Countersink nailheads, fill and sand smooth.
Remove rust, loose or peeling paint. Repair imperfections and sand smooth.
Wash off dirt, grease and chalk with detergent and/or powerwash.
Remove mildew stains with a mildew stain removing product.
Clean and sand new or weathered wood.
Scuff sand or degloss smooth or glossy surfaces.
Scuff sand or etch metals.
Rinse and allow to dry.
Caulk windows, doors and other openings.
Allow new stucco, plaster and masonry to cure for 30 days before painting.

Prime†

Use a product such as BEHR^® Multi-Surface Primer & Sealer No. 436.
For optimal colour development, better hide, and to reduce the number of topcoats with deep colours denoted with a dagger (†) on the colour chip, apply a custom tinted primer.
For best results, prime all metal surfaces before painting.
Prime all metal surfaces before painting.

Application

Apply when air and surface temperatures are between 2-32°C.
Stir paint occasionally.
Intermix containers of same product to ensure colour and sheen uniformity.
Use a high quality 10-13 mm nap roller cover, nylon/polyester brush or airless sprayer (.015-.021" spray tip, 60 mesh filter).
Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 250 mL per 3.79 L.
Certain colours may require more than one coat for complete hide. Darker colours may require additional dry time between coats.
Cooler temperatures or higher humidity may prolong drying time.
After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
Dry paint film is mildew resistant. When applying to vinyl, colour choice must be the same colour or lighter than the existing colour. Do not use on floors.

Disposal

For disposal of empty containers, unused paint and soiled rags, contact your household refuse collection service.

To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.

BEHR PREMIUM PLUS^® Exterior Flat

Ultra Pure White® No. 4050

Deep Base No. 4300

Medium Base No. 4400

BEHR PREMIUM PLUS^® Exterior Satin Enamel

Ultra Pure White® No. 9050

Deep Base No. 9340

Medium Base No. 9400

BEHR PREMIUM PLUS^® Exterior Semi-Gloss Enamel

Ultra Pure White® No. 5050

Deep Base No. 5340

Medium Base No. 5400

PREMIUM PLUS^® Interior / Exterior Hi-Gloss Enamel

Ultra Pure White® No. 8050

Deep Base No. 8300

Medium Base No. 8400

Red No. 8610 (Not 100% Acrylic)

Black No. 8620 (Not 100% Acrylic)

Behr Process Corporation warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

PRODUCT USAGE AND APPLICATION INSTRUCTIONS