BEHR DRYPLUS Masonry Waterproofer

Average Rating:
false

BEHR DryPlus is an advanced Interior/Exterior masonry waterproofer designed for porous concrete surfaces.

Ideal for basement and retaining walls.

Click Here to see available colours.


Finish

Flat Finish

Best for use in

Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks.

Coverage

7 - 12 m2 per 3.73 L


0
PRODUCT USAGE
Two paint rollers, two coat icon.

2 Coats Required
for Optimal Durability

Spread rate icon

Spread Rate:
Rough 7-9 m2
Smooth 9-12 m2

Clock icon

Dry Time:
1 HR Dry to Touch
4 HR Recoat

Soap and water cleaning a paint brush icon

Clean-Up:
Soap & Water

Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks.

Read More

Proper surface preparation is required

  • New or Unpainted Surfaces: New concrete must cure 30 days. Test for loose concrete by pressing masking/cellophane tape on surface, then pull off abruptly. If the tape doesn’t remove concrete, it can be painted. If concrete is removed, scrape down to a sound substrate.
  • Below grade application: Patch all holes or cracks with a fast setting hydraulic cement.
  • Above grade application: Remove mildew stains with a mildew stain removing product. All surfaces must be clean, free of dirt, efflorescence and oil. Clean surface with a product such as BEHR PREMIUM™ NO. 991 Cleaner & Etcher.
  • Previously Painted Surfaces: BEHR PREMIUM DryPlus NO. 875 provides best results on bare/untreated surfaces. PREVIOUSLY PAINTED SURFACES IN GOOD CONDITION MAY BE PAINTED. HOWEVER, BEHR WILL NOT GUARANTEE RESULTS. Test for loose concrete as stated under “New/Unpainted Surfaces” above. Remove deteriorated coatings. Follow all prep instructions under “New/Unpainted Surfaces” above.
Read More

  • Stir well before use.
  • Do not thin or apply at greater spread rate.
  • Use with adequate ventilation.
  • Use product when air/surface temperature is 10-32° C. Apply to dry or slightly damp surfaces. Wipe off any moisture before painting. Apply with a 13-19 mm nap roller, 4 cm nylon/polyester brush or an airless sprayer @ 155-225 kg/cm2 (2,200-3,200 lbs/in²) PSI using a .023 -.025 spray tip.
  • Two coats minimum are required: First Coat: Use a brush or roller, work onto the surface covering all pores or voids. Repeat for 2nd coat. Spot applications may be needed depending on porosity.
  • Important: If leaking persists after 2 coats, it indicates voids and pinholes are still open. Reapply to area.
Read More

  • Low temperatures or high humidity conditions will affect drying time.
  • Full cure should be reached in 7-14 days.
Read More

  • For disposal of empty containers and unused product contact your household refuse collection service.
Read More

To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.
Read More

Reviews

How-To

Find step-by-step instructions in our how-to articles and videos.

MSDS AND DATA SHEET

WARRANTY

Behr Process Corporation warrants to you, the original consumer purchaser, the performance of this product as described on this label for 10 years on vertical surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED, PREVIOUSLY UNCOATED AND PREVIOUSLY UNTREATED VERTICAL SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Colour fading and chalking will occur naturally over time. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Never miss out on the hottest deals and latest news from BEHR.

Please enter email address.
Please enter email address.