BEHR® WATER-BASED STAIN & POLY IN ONE

Average Rating:
false

BEHR Water-Based Stain & Poly in One delivers rich colour and protection in one easy step. This formula can be tinted to a wide range of popular interior colours and provides a warm look and durable protection to your interior wood surface. This high-performance stain & poly in one dries quick to a uniform finish, allowing you to shorten your project time and achieve beautiful results.

See Our Selection of Water-Based Wood Stains and Finishes


Finish

Available in Satin and Gloss finish.

Best for use in

Properly prepared interior surfaces such as furniture, moldings, cabinets, trim, and wood doors. Do not use on floors.

Coverage

11.6 m2 (125 Sq. Ft.) / 947 ml


0
PRODUCT USAGE
Icon of hand sanding surface with sanding block

Prep
Before Use

Icon of paint brush applying paint

2 Coats
Required

Icon representing length and width dimensions to determine square footage

Spread Rate:
125 Sq. Ft./Qt.

Icon of cleaning paint brush under water faucet

Clean-Up
Soap & Water

Properly prepared interior surfaces such as furniture, moldings, cabinets, trim, and wood doors. Do not use on floors.

CAUTION: Surface may be slippery when wet.

PROTECT FROM FREEZING. Do Not Use Without the Addition of Tinting Colourants.

Read More

Proper surface preparation is required.

FOR STRIPPED, UNSTAINED OR RAW WOOD:

  • Before starting, the surface must be dry, clean and free of dirt, grease, and glue.
  • Sand the wood in the direction of the grain using fine-grade sandpaper (#150-220 grit) until smooth.
  • Remove all sanding dust.
  • To help ensure uniform acceptance of stain colour and beautiful results, pretreat new or raw wood with BEHR® Water-Based Pre-Stain Wood Conditioner, following label directions.

FOR PREVIOUSLY FINISHED WOOD THAT IS NOT BEING STRIPPED:

  • Before starting, the surface must be dry, clean and free of dirt, grease, and glue.
  • Lightly sand the existing finish with 400 grit sandpaper to ensure adhesion.
  • Remove all sanding dust.
Read More

  • Stir BEHR Stain & Poly In One thoroughly before and occasionally during use. Do not thin.
  • Always test Stain & Poly on a scrap piece or hidden area of wood to verify desired colour.
Read More

  • Using a high-quality nylon/polyester bristle brush, dip approximately an inch into the can, gently tapping it against the inside to remove any excess.
  • Apply a very THIN, even coat following the direction of the grain.
  • Make sure to maintain a “wet” edge.
  • To minimize the brush marks and bubbles after staining, tip off the surface by holding the brush at a 45-degree angle and lightly run the bristles over the entire length of the wood.
  • Let the first coat dry for 1 hour or more.
  • Dry time may be extended due to high humidity, low temperatures, and inadequate ventilation or if the coat is applied too thick.
  • Lightly sand the surface between coats with fine sandpaper (#400 grit).
  • Remove all dust. Brush on a second thin coat following directions above.
  • To deepen the colour, apply a third coat.
  • NOTE: For additional protection, without adding colour, add a coat of BEHR Fast Drying Polyurethane.
  • Please refer to the back label of the container for application instructions.
Read More

  • For disposal of empty containers and unused product, contact your household refuse collection service
Read More

To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.

Read More

Reviews

Often Bought Together
BEHR<sup>®</sup> WATER-BASED PRE STAIN WOOD CONDITIONER
BEHR® WATER-BASED PRE STAIN WOOD CONDITIONER
Learn More
How-To

Find step-by-step instructions in our how-to articles and videos.

MSDS AND DATA SHEET

WARRANTY

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event this product proves to be defective within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Never miss out on the hottest deals and latest news from BEHR.

Please enter email address.
Please enter email address.