BEHR PREMIUM^® Transparent Log Home Gloss Finish

Where to Use

“For Wood Substrates Only” Exterior wood surfaces such as: Log and Timber Frame Homes, Siding, Fencing and Railings. Do not use on horizontal surfaces subject to foot traffic.

Usage Summary

Preparation

The following steps are recommended for best results.

• Use a product such as BEHR PREMIUM® NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
• BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner MUST be used following NO. 64 to clean, brighten & neutralize wood.
• When NO. 64 is not needed, use a product such as NO. 63 to clean and brighten the wood surface and to remove light to medium stains caused by mold, mildew, algae & fungus. On new wood, use a product such as NO. 63 to remove mill glaze and open the pores of the wood.
• Rinse thoroughly and allow to dry before coating.
• Lightly sand any remaining wood fibers/fuzz.

Application

• Must apply between 5-32˚ C. Do not use if rain is expected within 24 hours. The wood surface must be completely dry before application.
• Intermix multiple containers to ensure colour uniformity. DO NOT THIN PRODUCT.
• Stir product occasionally throughout application. Test product for colour on a small hidden area before proceeding.
• Use a 10 mm nap roller or nylon/polyester bristle brush. Airless sprayer with a .38 mm - .48 mm (.015 - .019") tip is recommended for experienced applicators only.
• Maintenance re-coating may be achieved by applying 2 coats at a spread rate of 18-37 m2 (200-400 sq. ft.) per 3.79 L over a clean, sound surface.
• Clean and recoat surface when finish no longer has gloss or luster or if the film is broken.
• Thoroughly seal the ends of the boards and all porous areas such as knots with several thin coats.
• Maintain a wet edge when applying. Back-brush during all application methods.
• Apply product end-to-end or to board lengths to prevent lap marks. Over application of finish will lead to surface failure including peeling and cracking.
• Avoid applying finish too heavily. Two coats required, 3-4 recommended.
• Avoid applying product in direct sunlight or on to hot surfaces.

Dry Time

• Dries to touch in 8-12 hours. Recoat after 24 hours. Cool temperatures and/or high humidity will require additional drying time.

Disposal

• For disposal of empty containers and unused product, contact your household refuse collection service.

For one year from the date of purchase, Behr Process Corporation warrants to the original residential consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product as described on this label when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext.2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.​