BEHR PREMIUM® Interior/Exterior Concrete & Garage Self-Priming 1-Part Epoxy
Beautify and protect your home's interior and exterior concrete surfaces with BEHR PREMIUM Concrete & Garage Self-Priming 1-Part Epoxy Floor Paint. This water-based paint can protect against hot-tire pick-up, automotive fluids and most household chemicals. This epoxy paint will provide a beautiful protective finish on driveways, garage floors, pool decks, walkways and interior concrete surfaces.
Finish
Satin finish
Best For Use In
Interior & Exterior concrete and masonry surfaces
Coverage
Rough Surface: 28-37 m2 ; Smooth: 37-46 m2
PRODUCT USAGE
-
Rough Surface
28-37 m2
Smooth Surface
37-46 m2 -
1 HR
Dry To Touch
4-6 HR
Recoat Time -
Clean-Up
Soap & Water -
Protect
from Freezing
Interior or Exterior surfaces such as: Porous Concrete, Masonry, Stone and Brick. Ideal for horizontal surfaces such as: Garage Floors, Driveways, Basement floors, Porches and Pool Decks. DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to fork-lifts.
Preparation
- Proper Surface Preparation is Required.
- All surfaces must be clean, sound, dry and free of any dirt, oil and grease.
New and Uncoated Concrete or Masonry Surfaces:
- Allow new surfaces to cure 30 days.
- For proper penetration and adhesion of topcoat, use a product such as BEHR PREMIUM CONCRETE & MASONRY CLEANER & ETCHER NO. 991 to clean and etch the surface. Follow all label instructions.
- Apply a product such as BEHR PREMIUM CONCRETE & MASONRY BONDING PRIMER NO. 880 to increase adhesion of topcoat to the surface. Follow all label instructions.
Painted, Stained or Sealed Concrete:
- Option 1- To completely strip the entire surface, use a product such as BEHR PREMIUM Concrete & Masonry Paint Striper NO. 992. Follow all label instructions.
- Option 2- To recoat over an existing coating, remove any loose or peeling paint and scuff sand the surface.
- Use a product such as BEHR PREMIUM CONCRETE & MASONRY DEGREASER & CLEANER NO. 990 to clean previously coated surfaces in sound condition.
- Use a product such as BEHR PREMIUM CONCRETE & MASONRY CLEANER & ETCHER NO. 991 to clean and etch any bare concrete area. Follow all label instructions.
- Spot prime all bare concrete areas with a product such as BEHR PREMIUM CONCRETE & MASONRY BONDING PRIMER NO. 880 to increase adhesion of topcoat to the surface. Follow all label instructions.
Read More
Application
- DO NOT THIN. Intermix all cans of same product to ensure colour uniformity. Stir before applying.
- Use product when air and surface temperatures are between 10-32°C.
- Apply a thin, even coat using a 10 mm nap roller cover, pad applicator or a nylon/polyester brush.
- Allow first coat to dry before deciding if a second coat is necessary. For uniformity apply a second coat (in a criss-cross direction).
- DO NOT APPLY MORE THAN TWO COATS. An annual touch-up may be required in areas subject to tire traffic.
Read More
Dry Time
- Longer dry time required in cooler temperatures and in higher humidity.
- The floor may be subjected to light foot traffic after 24 hours.
- Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture.
- Allow 7 days before subjecting to automotive tires.
- Premature heavy traffic will cause paint failure requiring spot recoating.
- If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours.
- Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed.
- Abrasive cleaners and pressure-washers should be used carefully to avoid premature paint failure.
Read More
Disposal
- Properly dispose of all soiled rags.
- To recycle or properly dispose of product in your community, contact your household refuse collection service.
Read More
To consult with a Behr Company Representative, call 1-800-661-1591.
Read More
Read More
Reviews
How-To
Find step-by-step instructions in our how-to articles and videos.
SDS AND DATA SHEET
BEHR PREMIUM® Interior/Exterior Concrete & Garage Self-Priming 1-Part Epoxy
See Full SDS, Product Data & SafetyWARRANTY
LIMITED WARRANTY: For one year from the date of purchase, Behr Paint Company warrants to the original consumer purchaser, (1) that the product meets Behr Paint Company manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Paint Company will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Quebec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Paint Company unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-661-1591, or contact Behr Paint Company at 110-600 Barlow Square S.E., Calgary, AB T2C 5T7. Behr Paint Company reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
