AIzaSyBMJLehm8j6j0La8w7yFA5HiR9WVNS8rHc

BEHR PRO® Block Filler Primer No. PR50

Avg. Rating:

BEHR PRO Block Filler Primer is a dependable solution for above-grade concrete surfaces, such as concrete block, cinder block, and poured or pre-cast concrete. It is an interior/exterior primer formulated to fill and seal porous masonry surfaces, reduce pin holing and provide a smooth surface prior to finish coat application.

Technical Data Sheets

Safety Data Sheets

Product Certifications & Declarations

Best for use in

Interior and Exterior

Coverage

7-9 m2 per 3.79 L

PRODUCT USAGE
  • Use on properly prepared, above-grade interior or exterior surfaces, such as concrete, concrete block/CMU, brick, cement board siding, stucco, and plaster.

Surface Preparation

  • The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew and release agents. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
  • Fill all gaps with paintable sealant and allow to completely dry prior to coating.
  • For maximum adhesion, glossy and slick surfaces must be de-glossed prior to coating.
  • This product is only designed to be used on unpainted masonry surfaces that have been allowed to cure(dry) at least 30 days with a moisture content below 15% before application.
  • Do not apply to shiny or slick surfaces or loss of adhesion may occur; these surfaces can be prepared with chemical etchers and/or sandblasting.
  • Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.

Read More

Application

  • Eye protection is recommended.
  • Use only when temperatures are between 10°C and 32°C.
  • Stir thoroughly before and occasionally during use. Apply using a brush, roller or spray.
  • For best results apply 2 coats and apply with airless sprayer. Backroll each coat working the material into the surface filling the masonry pores and voids.
  • Prime the entire surface to ensure a uniform appearance of the topcoat.
  • May be tinted with up to 2 ounces (59 ml) of universal colourant per gallon.
  • For airless spray applications, tip size should be .019 - .025.

Read More

Dry Time

  • Dries to touch in 1hour at 25°C and 50% humidity. Application at lower temperatures, high humidity or poor ventilation will affect dry time.
  • Recoat or topcoat after 2 hours.
  • Full Cure: 7 Days

Read More

Clean Up & Disposal

  • Clean equipment and paint splatters with warm, soapy water. If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.
  • Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

Read More

To consult with a Behr Company Representative, call 1-800-661-1591.

Read More

Read More

WARRANTY

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. THIS WARRANTY EXCLUDES (1) LABOUR AND COSTS OF LABOUR FOR THE APPLICATION OR REMOVAL OF ANY PRODUCT, AND (2) ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON BREACH OF EXPRESS OR IMPLIED WARRANTY, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-661-1591, or contact Behr Process Corporation at 110-600 Barlow Square S.E., Calgary, AB T2C 5T7. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Read More

Reviews

Pro Contractor wearing a cap and shirt with Behr

PAINTING CONTRACTORS

Professional products and services specifically designed for residential and commercial painting contractors.

FOR CONTRACTORS
A small image of a Property Manager showing a BEHR PRO Rep a multi-family complex. The property manager is pointing at something while the BEHR PRO Rep is looking at what she is pointing and taking notes on a laptop.

PROPERTY & FACILITY MANAGERS

A full range of products and services to help property and facility managers enhance and maintain the appearance of properties.

FOR PROPERTY MANAGERS

READY TO GET STARTED?

Contact a Behr Pro Rep Icon

CONTACT A BEHR PRO® REP

Your reputation depends on your ability to do the job right. BEHR can help.

Find a rep
Technical Services Icon

TECHNICAL SERVICES

1-800-661-1591
Mon - Fri, 6am-3pm PST
Sat. & Sun., Closed

PRO XTRA logo

JOIN THE HOME DEPOT® PRO XTRA LOYALTY PROGRAM

Get 10% - 20% Back in Quarterly Rewards
BEHR® Paints, Stains & Primers.

sign up on homedepot.ca