BEHR PREMIUM^® Granite Grip^™ No. 650

Where to UseBlank space if empty.

Interior/Exterior surfaces such as: Porous Concrete, Masonry, Stone and Brick. Ideal for horizontal surfaces such as: Garage Floors, Driveways, Walkways, Patios, Porches and Pool Decks. 

Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.

READY TO USE OR ADD TINTING COLOURANTS

Usage SummaryBlank space if empty.

Where Not to UseBlank space if empty.

May be used on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts.

Preparation†Blank space if empty.

Proper surface preparation is required.

• All surfaces must be clean, sound, dry and free of any dirt, oil and grease. 

For Uncoated Concrete or Masonry:

• Allow new surfaces to cure 30 days. 
• Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer's label directions) to achieve a textured proile similar to 150 grit sandpaper. 

For Previously Coated Surfaces: 

• For a painted surface in sound condition, use a product to clean and prepare the surface. 
• If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface. 
• Scuff sand glossy surfaces. 
• Clean and spot etch any exposed concrete. 
• Remove all dust with a damp cloth, allow to dry.

ApplicationBlank space if empty.

• DO NOT THIN. Intermix all cans of the same product to ensure colour uniformity.
• Stir before and occasionally during application.
• Use product when air and surface temperatures are between 10-32° C.
• Apply to dry concrete. Do not apply if rain or heavy dew is expected within 24 hours.
• Do not apply in direct sunlight.
• Tape off any adjacent areas and apply to the edges using a nylon/polyester brush.
• For hairline cracks up to 2 mm, completely fill in with coating using a brush and allow to dry completely prior to roller application.
• Apply an even first coat using a 6 mm adhesive roller cover or nylon/polyester brush.
• NOTE: The first coat will act as the base coat and it will not completely cover the surface by design. Avoid over application on the first coat.
• Apply from a roller tray or pour directly from the container
• NOTE: Pouring can help spread the coating quickly however it may reduce the overall spread rate.
• Work in areas approximately 1 m x 1 m.
• Pour a circular (pancake style) shape with a 25 cm diameter of the working area.
• Spread from the center outwards, rolling in multiple directions to evenly distribute.
• For long, narrow areas, pour a strip about 8 -12 cm across the surface.
• Apply moderate pressure to the roller to push the coating outwards and even out the surface.
• Work quickly and overlap the previously coated areas to ensure full coverage.
• Avoid regular patterns and knock down hard edges using the roller.
• Allow first coat to dry then apply second coat in the same method as the first coat.
• While two coats are necessary, additional coats may help hide previous surface imperfections or cover over contrasting colours.
• For large projects, consider using a texture sprayer with a 4mm tip.
• Spray in 1.2 m x 1.2 m sections and back roll with 6 mm adhesive roller cover.

Dry TimeBlank space if empty.

• Longer dry time required in cooler temperatures and in higher humidity. 
• The floor may be subjected to light foot traffic after 24 hours. 
• Allow 72 hours before subjecting surface to automotive tires, heavy foot traffic or repositioning furniture. 
• Premature heavy traffic will cause paint failure requiring spot recoating.

Clean UpBlank space if empty.

• Soap & water clean-up.
• Wait at least 30 days before rinsing or cleaning. 
• Use a mild detergent as needed. 
• Abrasive cleaners and pressure-washers should be used carefully to avoid premature coating failure. 

DisposalBlank space if empty.

• Properly dispose of all soiled rags. 
• To recycle or properly dispose of product in your community, contact your household refuse collection service.

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.