BEHR ULTRA^™ Exterior Semi-Gloss Enamel No. 5850

Where to UseBlank space if empty.

Properly prepared and cleaned coated or uncoated exterior surfaces. Ideal for Wood, Vinyl, Aluminum, Fiber Cement Siding, Metals, Brick, Masonry, Stucco, Doors, Windows, Trim, Shutters, Steel, Fences, Garage Doors, Outdoor Furniture, Railing and Wrought Iron.

Usage SummaryBlank space if empty.

Preparation & Prime†Blank space if empty.

• Countersink nailheads, fill and sand smooth.
• Remove rust, loose or peeling paint.
• Repair imperfections and sand smooth.
• Wash off dirt, grease and chalk with detergent and/or powerwash.
• Remove mildew stains with a mildew stain removing product.
• Clean and sand new or weathered wood.
• Scuff sand or degloss smooth or glossy surfaces.
• Scuff sand or etch metals.
• Rinse and allow to dry.
• Caulk windows, doors and other openings.
• Allow new stucco, plaster and masonry to cure for 30 days before painting.
• Use BEHR ULTRA paint as a primer for repaired or uncoated surfaces, including woods that contain tannins (two primer coats required for redwood and cedar) and heavily stained areas.
• Lock in stains with the first primer coat; if necessary, apply a second primer coat of BEHR ULTRA.
• For drastic colour changes or when applying deep colours denoted with a dagger (†) on the colour chip, apply a tinted primer coat of BEHR ULTRA if needed.

ApplicationBlank space if empty.

• Apply product on dry substrates when air and surface temperatures are between 2°-32°C and will remain between 2°-32°C for at least 4 hours after applying.
• Allow paint film to dry for at least 60 minutes prior to rain showers when temperatures are between 15°-21° C and 60-70% relative humidity.
• Lower temperatures, higher humidity or deep colours may increase dry time and/or rain resistance time.
• Stir paint occasionally. Intermix containers of same product to ensure colour and sheen uniformity.
• On semi-smooth surfaces, use a high quality 10-13 mm nap roller cover, nylon/polyester brush or an airless sprayer (.015 -.021" spray tip, 60 mesh filter).
• On rough surfaces, use a high quality 19-25 mm nap roller cover.
• Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 250 mL per 3.79 L
• Certain colours may require more than one coat for complete hide.
• On heavy stains and woods that contain tannins, allow 12-16 hours of dry time between coats.
• Cooler temperatures or higher humidity may prolong drying time.
• After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
• Dry paint film is mildew resistant.
• When applying to vinyl, colour choice must be the same colour or lighter than the existing colour.
• Do not use on floors.

DisposalBlank space if empty.

• For disposal of empty containers, unused paint and soiled rags, contact your household refuse collection service.

Behr Process Corporation warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.