BEHR® Fast-Drying Water-Based Polyurethane No. B8106
BEHR Fast Drying Water-Based Polyurethane is a clear protective finish that shields your interior wood surfaces that are stained with BEHR Water-Based Wood Stain. This durable polyurethane is designed to prolong the life of your wood surface and create a smooth, lasting finish. This product enhances the look and colour of your wood surface, allowing its true beauty to shine through. Multiple sheens are available depending on your desired look.
See Our Selection of Interior Water-Based Wood Stains and Finishes
Safety Data Sheets
Finish
Available in Matte, Satin, Semi-Gloss, and Gloss Finish
Best For Use In
Properly prepared interior bare or stained wood surfaces such as furniture, mouldings, cabinets, trim, doors and residential hardwood floors.
Coverage
11.6 m2 per 947 ml.
-
Prep
Before Use -
2 Coats Required
3 Coats if Desired -
Spread Rate:
11.6 m2 per 947 ml. -
Clean-Up
Soap & Water
READY TO USE. PROTECT FROM FREEZING.
Properly prepared interior bare or stained wood surfaces such as furniture, moldings, cabinets, trim, doors and residential hardwood floors.
CAUTION: Top coated surfaces may be slippery when wet.
Surface Preparation
The following steps are recommended for the best results.
- For refinishing, remove all wax or cleaner build-up with a wax stripper or degreaser prior to sanding.
- Sand all surfac.es in the direction of the wood grain to desired smoothness
- DO NOT USE steel wool.
- Remove all dust from sanded surfaces and clean with a tack cloth.
Read More
Application
- Do not shake or thin.
- Do not apply in direct sunlight or in temperatures below 10°C or above 32°C.
- Stir thoroughly prior to and during use.
- If wood stain colour is desired, apply BEHR® Wood Stain. Follow all label instructions.
- Using a high-quality nylon/polyester bristle brush, dip approximately an inch into the can, gently tapping it against the inside to remove any excess.
- Apply a thin, even coat following the direction of the grain making sure to maintain a wet edge.
- To minimize the brush marks and bubbles after staining application, tip off the surface by holding the brush at a 45-degree angle and lightly run the bristles over the entire length of the wood.
- Floor Application: use a synthetic pad applicator or bristle brush and maintain a wet edge to avoid lap marks.
- For maximum durability, 3 coats are required.
- Do not puddle, over-brush or overlap finishes.
- Sand lightly between coats with fine sandpaper.
- Remove all dust prior to applying additional coats.
Read More
Dry Time
- Dries to touch in 1 hour.
- Sand or Recoat: 1 hour.
- After the final coat, allow 12 - 24 hours before light use.
- Fully cured: 3 days after the final coat.
Read More
Disposal
- For disposal of empty containers and unused product, contact your household refuse collection service
Read More
To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.
Read More
Read More
LIFETIME LIMITED WARRANTY
For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. THIS WARRANTY EXCLUDES (1) LABOUR AND COSTS OF LABOUR FOR THE APPLICATION OR REMOVAL OF ANY PRODUCT, AND (2) ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON BREACH OF EXPRESS OR IMPLIED WARRANTY, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-661-1591, or contact Behr Process Corporation at 110-600 Barlow Square S.E., Calgary, AB T2C 5T7. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
Read More
Reviews
PAINTING CONTRACTORS
Professional products and services specifically designed for residential and commercial painting contractors.
FOR CONTRACTORS
PROPERTY & FACILITY MANAGERS
A full range of products and services to help property and facility managers enhance and maintain the appearance of properties.
FOR PROPERTY MANAGERSREADY TO GET STARTED?
CONTACT A BEHR PRO® REP
Your reputation depends on your ability to do the job right. BEHR can help.
Find a rep
JOIN THE HOME DEPOT® PRO XTRA LOYALTY PROGRAM
Get 10% - 20% Back in Quarterly Rewards
BEHR® Paints, Stains & Primers.
About Interior Paint Sheens
Get the look you want and the protection you need for any room in your home.
A flat sheen has a non-reflective finish that touches up well and hides minor surface imperfections.
Low-traffic areas; interior walls and ceilings
Ceilings
Medium-Low
A matte sheen has a low-luster, reflective finish that is durable, easy to clean, touches up well and also hides minor surface imperfections.
Low-traffic areas; interior walls
Family rooms, living rooms, kids' rooms, bathrooms, dining rooms, ceilings
Medium
An eggshell enamel sheen has a soft, velvety appearance that resists dirt and grime, as well as mildew.
Moderate-traffic areas
Family rooms, living rooms, bedrooms, kids' rooms, hallways, dining rooms
Medium
A satin enamel sheen has a pearl-like finish that's easy to clean.
All interior surfaces; moderate- to high-traffic areas
Family rooms, living rooms, bedrooms, kids' rooms, hallways, kitchens, bathrooms, doors, windows, trim, cabinets, shutters, interior furniture
Medium-High
A semi-gloss enamel sheen is sleek and radiant resisting mildew, moisture and wear.
Cabinets and trim; high-traffic, high-moisture areas
Kids' rooms, hallways, kitchens, bathrooms, doors, windows, trim, cabinets, shutters
High
Hi-Gloss enamel sheens provide have a brilliant, shiny appearance and a durable, glass-like finish that allows dirt and grime to be wiped clean.
High-use surfaces
Kitchens, bathrooms, doors, windows, trim, cabinets, shutters, interior furniture
High
About Exterior Paint Sheens
Set the right curb appeal with exterior painting efforts that last.
A flat sheen is non-reflective, and easy to apply and touch up. It will minimize the appearance of minor surface imperfections.
Wood and vinyl walls and siding; brick and other masonry; fences
Medium-Low
A satin enamel sheen creates a pearl-like finish that's durable and dirt-resistant. It will also resist moisture, fading and stains.
Virtually all exterior surfaces
Medium-High
A semi-gloss enamel sheen is sleek and radiant with a hard, durable finish. It is formulated to withstand wear, and will also resist moisture, fading and stains.
Doors, trim and shutters; Exterior furniture
High
Hi-Gloss enamel sheen have a brilliant, shiny appearance and a durable, glass-like finish that allows dirt and grime to be wiped clean.
High-use surfaces
High
- Free Same-Day, Next-Day Delivery*
- Call, Text, or Email Your Paint Order
- Will Call & Schedule Deliveries
- Custom Color Matching
- Product & Record Order Management
- Expert Paint Knowledge
- Get 10%-20% back in quarterly rewards on BEHR® Products when you join Home Depot's Pro Xtra™ loyalty program
- Call, Text or E-mail your orders to your dedicated BEHR PRO Paint Specialist
- Arrange will call & Schedule Deliveries for pick-up at your Home Depot location or for delivery to you
