BEHR^® Water-Based Stain & Poly in One No. B6362

Where to UseBlank space if empty.

Properly prepared interior surfaces such as furniture, moldings, cabinets, trim, and wood doors. Do not use on floors.

CAUTION: Surface may be slippery when wet.

PROTECT FROM FREEZING. Do Not Use Without the Addition of Tinting Colourants.

Usage SummaryBlank space if empty.

PREPARATIONBlank space if empty.

Proper surface preparation is required.

FOR STRIPPED, UNSTAINED OR RAW WOOD:

• Before starting, the surface must be dry, clean and free of dirt, grease, and glue.
• Sand the wood in the direction of the grain using fine-grade sandpaper (#150-220 grit) until smooth.
• Remove all sanding dust.
• To help ensure uniform acceptance of stain colour and beautiful results, pretreat new or raw wood with BEHR^® Water-Based Pre-Stain Wood Conditioner, following label directions.

FOR PREVIOUSLY FINISHED WOOD THAT IS NOT BEING STRIPPED:

• Before starting, the surface must be dry, clean and free of dirt, grease, and glue.
• Lightly sand the existing finish with 400 grit sandpaper to ensure adhesion.
• Remove all sanding dust.

PRODUCT PREPARATION AND COLOUR TESTINGBlank space if empty.

• Stir BEHR Stain & Poly In One thoroughly before and occasionally during use. Do not thin.
• Always test Stain & Poly on a scrap piece or hidden area of wood to verify desired colour.

APPLICATIONBlank space if empty.

• Using a high-quality nylon/polyester bristle brush, dip approximately an inch into the can, gently tapping it against the inside to remove any excess.
• Apply a very THIN, even coat following the direction of the grain.
• Make sure to maintain a “wet” edge.
• To minimize the brush marks and bubbles after staining, tip off the surface by holding the brush at a 45-degree angle and lightly run the bristles over the entire length of the wood.
• Let the first coat dry for 1 hour or more.
• Dry time may be extended due to high humidity, low temperatures, and inadequate ventilation or if the coat is applied too thick.
• Lightly sand the surface between coats with fine sandpaper (#400 grit).
• Remove all dust. Brush on a second thin coat following directions above.
• To deepen the colour, apply a third coat.
• NOTE: For additional protection, without adding colour, add a coat of BEHR Fast Drying Polyurethane.
• Please refer to the back label of the container for application instructions.

DISPOSALBlank space if empty.

• For disposal of empty containers and unused product, contact your household refuse collection service

Blank space if empty.

To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event this product proves to be defective within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.