BEHR PREMIUM^® Porch & Patio Anti-Slip Floor Paint - Textured Low-Lustre Enamel No. 6250

Where to UseBlank space if empty.

This product is ideal for porches, floors, decks, basements, patios, and ramps. Not for use on garage floors or areas subject to automotive traffic. Use on previously painted or primed interior or exterior surfaces such as: Wood, Concrete, or Composite Wood.

Usage SummaryBlank space if empty.

PreparationBlank space if empty.

• New or Weathered Wood: Use a product such as BEHR PREMIUM^® No. 63 All-In-One Wood Cleaner. Lightly sand to remove remaining wood fibers/fuzz.
• Note: WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.
• Painted Surfaces-Wood: For a painted surface in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper to remove old coating. Scuff sand glossy surfaces. Use stainless steel or galvanized nails to prevent nail staining. Countersink nail heads, repair imperfections and sand smooth. Remove all dust with a damp cloth, allow to dry.
• Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Clean and etch surface using a product such as BEHR PREMIUM^® Concrete & Masonry Cleaner & Etcher to achieve a textured profile similar to 150 grit sandpaper. Wipe your fingers over the clean, dry floor to check for dust or powder. Ensure there is no residue on your fingers that may have been left from the etcher. If residue is found, rinse the surface to remove residue. Allow the surface to dry completely. Sprinkle a few drops of water onto the surface. If water is quickly absorbed and the surface feels like 150 grit sandpaper, the surface is ready. If not, re-etch.
• Painted Surfaces-Concrete: For a painted surface in sound condition, use a product to clean and prepare the surface. If the coating is failing or peeling, use a paint stripper such as BEHR PREMIUM^® No. 992 Concrete & Masonry Paint Stripper to remove old coating or scrape/sand down to a sound concrete surface. Scuff sand glossy surfaces. Clean and spot etch any exposed concrete. Remove all dust with a damp cloth, allow to dry.

PrimeBlank space if empty.

• Interior Wood: Use a product such as BEHR^® No. 75 Kitchen, Bath & Trim Stain-Blocking Primer & Sealer
• Exterior Wood: Use a product such as BEHR^® No. 436 Multi-Surface Primer & Sealer.
• Interior/Exterior Concrete or Masonry: Over uncoated concrete or masonry surfaces, use a product such as BEHR PREMIUM No. 880 Concrete & Masonry Bonding Primer.

ApplicationBlank space if empty.

• Brush: Nylon/polyester
• Roller: 10 mm nap roller, depending on surface texture
• Spray: Texture sprayer capable of 1.0GPM with a 3 mm tip.  Do not use with airless sprayer. Thinning: Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 236 ml per 3.78 L.
• Dry Time: 10-32° C & 50% Relativity Humidity To Touch: 2 hours, To Recoat: 2-4 hours
• Dry times are temperature, humidity, and film thickness dependent.

DisposalBlank space if empty.

• Clean all tools and equipment with clean water. Properly dispose of all soiled rags. For disposal of empty containers and unused product, contact your household refuse collection service.

To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.

For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.