BEHR PREMIUM® Transparent Penetrating Oil Wood Finish
This easy to apply oil base transparent finish enhances the natural beauty of wood. It provides UV protection and is low maintenance. It also features a mildew resistant finish and is ideal for new to slightly weathered uncoated and unsealed exterior wood surfaces.
READY TO USE, PROTECT FROM FREEZING.
Finish
Creates a Clear Finish that showcases the full natural beauty of the wood.
Best For Use In
Recommended for properly prepared new to slightly weathered, unsealed exterior wood surfaces.
Coverage
23-28 m2
PRODUCT USAGE
-
Must Prep
Before Applying
Wood Finish -
1 Coat
Application -
Spread Rate:
Covers 23-28 m2 -
Clean-Up:
Mineral Spirits
or Paint Thinner
Recommended for properly prepared new to slightly weathered, unsealed exterior wood surfaces (0-5 years exposure) such as; Decks, Railings, Shakes, Shingles, Siding, Fences, and Wood Patio Furniture.
Preparation
PROPER SURFACE PREPARATION IS REQUIRED.
- For failing coatings or to remove loose wood fibers, use a product such as BEHR PREMIUM® No. 64 Wood Stain & Finish Stripper followed by BEHR PREMIUM No. 63 All-In-One Wood Cleaner to neutralize the wood.
- When No. 64 is not needed, a product such as No. 63 MUST be used to remove mill glaze and clean the wood surface.
- After using either No. 64 or No. 63, rinse thoroughly with a garden hose or pressure washer.
- When rinsing with a pressure washer, use the broadest spray pattern while keeping the nozzle at least 24" away from the surface. Allow the area to dry at least 24 hours before coating.
- Lightly sand to remove remaining wood fibers/fuzz.
Read More
Application
For best results, a pad applicator is recommended over large deck areas.
- Must apply between 5-32˚C.
- Avoid applying in direct sunlight or to hot surfaces. Do not use if rain is expected within 24 hours.
- The surface must be completely dry before application. Intermix multiple containers to ensure colour uniformity.
- DO NOT THIN PRODUCT. Stir product occasionally throughout the application.
- Test product for penetration and colour on a small hidden area before proceeding.
- Use a natural bristle brush for areas requiring more accuracy. Use of rollers should be limited to rough surfaces only. Use 10 mm nap or longer when appropriate.
- A high quality pump sprayer with a variable tip or an airless sprayer with a .33 -.43 mm tip (60 mesh filter) may be used.
- Lightly saturate the surface and back-brush any excess finish by using pad applicator.
- Be sure to eliminate puddling and evenly distribute the finish.
- Maintain a wet edge when applying. Apply product end-to-end or to board lengths to prevent lap marks.
- Avoid applying finish too heavily. One coat application.
- For optimum performance, coat all accessible sides.
Read More
Maintenance
- When colour has faded and water is readily absorbed by the substrate, prep/clean with a product such as BEHR PREMIUM No. 63, allow to dry, and apply a new/fresh coat of wood finish.
- Product can be applied annually if needed.
Read More
Dry Time
- Dry to touch after 2-4 hours depending on wood porosity.
- 24-48 hours before foot traffic. 72 hours for full cure.
Read More
Disposal
- For disposal of empty containers and unused product, contact your household refuse collection service.
Read More
To consult with a Behr Company Representative, call 1-800-661-1591.
Read More
Read More
Reviews
Often Bought Together
How-To
Find step-by-step instructions in our how-to articles and videos.
SDS AND DATA SHEET
BEHR PREMIUM® Transparent Penetrating Oil Wood Finish
See Full SDS, Product Data & SafetyWARRANTY
LIMITED WARRANTY: For one year from the date of purchase, Behr Paint Company warrants to the original consumer purchaser, (1) that the product meets Behr Paint Company manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Paint Company will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Quebec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Paint Company unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-661-1591, or contact Behr Paint Company at 110-600 Barlow Square S.E., Calgary, AB T2C 5T7. Behr Paint Company reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
